Humic Acid Explained: How Leonardite Rebuilds Soil Health and Lifts Nutrient Uptake
Growers rarely buy humic acid because it looks impressive on a label. They buy it because a field that has been farmed for twenty years stops responding the way it used to: fertiliser rates creep up, water runs off instead of soaking in, and roots stay in the top few centimetres. Humic acid is one of the few inputs that addresses all three problems at the same time.
What humic acid actually is
Humic acid is the alkali-soluble fraction of highly decomposed organic matter. It is not a single molecule but a family of large aromatic compounds carrying carboxylic and phenolic groups. Those functional groups are the reason humic acid behaves the way it does: they carry a negative charge, they hold water, and they bind metal ions.
In practice that means three commercial facts matter more than the marketing story:
- It is measured by content, not by colour. A dark powder can still be 30% humic acid, while a lighter granule can test at 65%.
- Source determines quality. Leonardite, weathered brown coal and peat all give different molecular weights and different salt loads.
- Solubility drives application method. Granules for soil, powder for drip and fertigation, liquid for quick response.
Why leonardite is the preferred raw material
Leonardite is oxidised lignite formed over millions of years, typically 60 to 90 million in the case of the deposits we work with. Because it has already been through oxidation, its humic acid content is high (often 40 to 70% before extraction) and the fraction is mature: larger molecules, more stable in soil, slower to leach.
Young compost or peat extracts contain more fulvic and low-molecular fractions. They act faster but disappear faster. For a base application before planting, leonardite-derived potassium or sodium humate is the more cost-effective choice.
Four mechanisms that matter in the field
- Cation exchange capacity. Humic acid adds exchange sites that hold calcium, magnesium and potassium against leaching, then release them to the root as the plant demands them.
- Chelation. Iron, zinc and manganese are locked up in alkaline soils. Humates complex these micronutrients and keep them plant-available, which is why humic acid plus a micronutrient mix usually outperforms either product alone.
- Aggregate stability. Polysaccharide and humic fractions glue soil particles into aggregates, improving infiltration and root respiration. This is the effect growers notice first in compacted or high-sodium soils.
- Microbial stimulation. Humic substances serve as a carbon source and electron shuttle for soil microbes, supporting the rhizosphere community that mineralises nutrients.
Application rates that work
| Method |
Product |
Typical rate |
Timing |
| Soil broadcast |
Humic acid granule 50–60% |
150–300 kg/ha |
Before planting, incorporated |
| Band / side dress |
Potassium humate flake 70% |
15–30 kg/ha |
At sowing or first irrigation |
| Drip / fertigation |
Liquid humate 12–15% |
15–30 L/ha per cycle |
Every 10–14 days |
| Foliar |
Soluble humate or fulvate |
1–2 kg/ha |
Vegetative growth, after stress |
Rates should be adjusted to organic matter content: a soil below 1% organic matter responds strongly, a soil above 3% needs the product mainly for micronutrient chelation rather than structure.
What to check on a supplier’s COA
Ask for a certificate of analysis that states humic acid content on a dry basis, moisture, pH, potassium oxide (K2O) or sodium content, and screen size. Also ask two practical questions: is the product fully soluble in hard water at field dilution, and does the supplier declare the raw material origin. A supplier who cannot answer both is reselling, not manufacturing.
Our humic acid range covers granules, powder, flakes and liquid, all produced from leonardite in Tianjin. If you send us your soil test and target rate, we will recommend the grade and the packing that fits your market. Request a quote.
Fulvic Acid vs Humic Acid: What’s the Difference and When to Use Each
The two names appear together on almost every biostimulant label, which is why so many buyers assume they are interchangeable. They are not. The difference is one of the most useful pieces of knowledge a purchaser can have, because it decides whether a product belongs in the soil or on the leaf.
The one-line difference
Humic acid is soluble only in alkaline solution. Fulvic acid is soluble in water at any pH. Everything else follows from that: molecular size, mobility in soil, whether it can pass through a leaf surface, and how it is applied.
Side-by-side comparison
| Property |
Humic acid |
Fulvic acid |
| Solubility |
Alkaline only (pH > 8) |
Water, any pH |
| Molecular weight |
High (10,000–100,000 Da) |
Low (1,000–10,000 Da) |
| Main effect |
Soil structure, CEC, slow release |
Chelation, foliar uptake, stress response |
| Best application |
Soil, base dressing, granule |
Foliar, drip, seed treatment |
| Residual in soil |
Weeks to months |
Days |
| Cost per kg |
Lower |
Higher |
When fulvic acid is the right choice
- Foliar programmes. The low molecular weight lets fulvic acid pass the cuticle and move in the phloem, carrying chelated micronutrients with it.
- Fertigation in alkaline water. Fulvic acid stays in solution where humate would precipitate and block drippers.
- Recovery after stress. Heat, salinity, transplanting and herbicide stress are where growers report the clearest return.
- Seed treatment. Low rates (0.5–1 L per tonne of seed) improve germination uniformity.
When humic acid is the right choice
- Building soil organic matter. You need volume and persistence; large humic molecules stay in the topsoil and keep working.
- Sandy or degraded soils. Exchange capacity is the limiting factor, and granule or flake humate lifts it at a low cost per hectare.
- Saline and sodic soils. Humate improves aggregate formation and helps displace sodium, especially combined with gypsum.
The commercial view
A common mistake in formulation is to replace humate with fulvate to look more premium, then apply it at the same rate. Because fulvic acid is dosed 5 to 20 times lower, the cost per hectare of a genuine fulvic programme can still be higher than a humate base dressing. The correct approach is usually both: humate to the soil as a foundation, fulvate to the leaf at the moments that matter.
We produce bio fulvic acid (powder and liquid) and potassium fulvate from the same leonardite feedstock, so both fractions are consistent batch to batch. Tell us your crop and application method and we will quote the right grade. Contact our team.
How to Apply Potassium Humate: Rates, Timing and Crop Guide
Potassium humate sits between raw humic acid and a straight potassium fertiliser. It carries both the humic fraction that conditions soil and 8 to 12% K2O in a form plants can take up, which makes it the grade most agronomists specify first when a grower wants one product to do two jobs.
Choose the right physical form
- Flakes (70–80% humic acid). The export standard. Dissolves readily in water, ideal for fertigation and for repacking under your own brand.
- Powder (60–70%). Fastest dissolution for foliar and seed treatment; more dust, so packing quality matters.
- Granule (50–60%). For soil broadcast and blending with NPK. Use a granule that resists abrasion in a blender.
- Liquid (12–15%). Convenient for pivot and drip systems, higher freight cost per unit of humic acid.
Rates by application method
| Method |
Rate |
Water volume |
Notes |
| Soil broadcast |
20–40 kg/ha |
— |
Incorporate before planting |
| Drip fertigation |
3–6 kg/ha per cycle |
200–400 L/ha |
Every 10–15 days, flush lines after |
| Foliar |
0.5–1 kg/ha |
300–500 L/ha |
Early morning or evening |
| Seed treatment |
0.3–0.5 kg per 100 kg seed |
Slurry |
Dry in shade before sowing |
Crop-specific notes
Vegetables (tomato, pepper, cucumber, leafy greens). Split the total between transplant drench and two or three fertigation cycles. Response is strongest in the first three weeks after transplanting, when root volume is being established.
Fruit trees and vines. Apply in the root zone at bud break and again after harvest. On calcareous soils, combine with a chelated iron source to correct chlorosis faster than either product alone.
Field crops (wheat, maize, rice, cotton). Granule at sowing is the most economical route. On rice, apply to the paddy before the last puddling so the humate stays in the root zone.
Turf and ornamentals. Low-rate monthly foliar keeps colour without pushing excessive growth; combine with a light nitrogen programme.
Mixing cautions
- Do not tank-mix with concentrated calcium or high-hardness water — precipitation wastes the product and blocks filters.
- Run a jar test: 1 g product in 100 mL of the actual spray water, stir, stand 30 minutes. Any sediment means dilute further or use a different water source.
- Keep the spray solution pH between 6 and 8. Very acidic solutions reduce solubility.
- Do not mix with strongly oxidising agents such as hypochlorite.
Our potassium humate is available in flake, crystal, powder and granule form, 70% and 80% humic acid, packed 25 kg net with OEM branding on request. Get a quotation.
Seaweed Extract as a Biostimulant: Root Growth, Yield and Stress Tolerance
Seaweed extract is the most widely used biostimulant in the world, and also the most inconsistently specified. Two products can both say “100% seaweed extract” and behave completely differently in the field, because the extraction method decides which compounds survive.
What is actually in the extract
- Cytokinins and auxins. Natural plant hormones that drive cell division and root initiation — the main reason seaweed works on transplant establishment.
- Betaines and mannitol. Osmoprotectants that help plants hold water under heat, drought and salinity.
- Alginates and fucoidans. Polysaccharides that improve soil aggregation and trigger plant defence responses.
- Trace minerals. Iodine, boron, zinc and iron in plant-available form.
Cold process or alkaline hydrolysis
Alkaline hydrolysis (usually potassium hydroxide at high pH and temperature) gives high yields and a clean, fully soluble powder, but it degrades part of the hormone fraction. Cold or physical extraction preserves more of the labile compounds but gives a lower concentration and a shorter shelf life.
For most export programmes the practical answer is a well-controlled alkaline process with a declared alginate and cytokinin content, plus a guaranteed solubility figure. Ask for the extraction method in writing — a supplier who will not state it is usually buying bulk powder and re-bagging.
Application programme
| Stage |
Method |
Rate |
Goal |
| Transplant / sowing |
Root dip or soil drench |
2–3 kg/ha |
Root initiation, establishment |
| Vegetative growth |
Foliar |
1–1.5 kg/ha every 14 days |
Canopy development |
| Flowering / fruit set |
Foliar |
1–2 kg/ha |
Reduce drop, improve set |
| Stress events |
Foliar, before and after |
1.5–2 kg/ha |
Heat, cold, salinity recovery |
What results are realistic
Published trials and our customers’ field data point to single-digit yield gains in most arable crops — typically 3 to 8% — and larger effects where stress is the limiting factor or where root establishment decides the season, such as transplanted vegetables and young orchards. Seaweed extract is not a substitute for balanced nutrition. It works best as the last 5% of a programme that is already correct.
Buying checklist
- Declared alginate or fucoidan content, not just “seaweed extract”.
- Potassium content (K2O 8–18% is typical for alkaline extracts).
- Solubility: a 1% solution should be clear with no sediment after 30 minutes.
- Heavy metal and arsenic report for EU and Japanese markets.
- Mesh size matched to your application — 60–80 mesh for foliar, 40 mesh for soil.
Our seaweed extract series is available as flake, powder and liquid, packed in 1 kg foil bags up to 25 kg drums. Ask for a sample and COA.
Sodium Humate: Industrial, Feed and Agricultural Applications
Most agricultural buyers treat sodium humate as a budget alternative to potassium humate. That is a narrow view. Sodium humate is the grade of choice in several industrial markets where its dispersing and binding behaviour matters more than its potassium content, and where the sodium load is irrelevant or even useful.
Grades and specifications
| Grade |
Humic acid |
Appearance |
Main market |
| Flakes |
65–75% |
Black, shiny |
Drilling fluid, agriculture |
| Shiny crystal |
70–80% |
Granular crystal |
Ceramic, water treatment |
| Powder |
60–70% |
Fine black powder |
Feed additive, blending |
Drilling fluid additive
In water-based drilling muds, sodium humate works as a filtration control and shale inhibition agent. It reduces fluid loss, stabilises the borehole wall and tolerates the high temperatures found in deep wells, which is why it is specified in API-grade mud programmes. Typical dosage is 2 to 8 kg per cubic metre of mud, adjusted to salinity and temperature.
Ceramic and construction
Sodium humate acts as a deflocculant and binder in ceramic bodies and as a green-strength additive in refractory mixes. It improves slip rheology at very low addition rates (0.1–0.5%), replacing more expensive synthetic dispersants.
Water treatment and environmental use
The high density of carboxylic groups makes sodium humate an effective adsorbent for heavy metals and an anionic polyelectrolyte in wastewater treatment. It is also used in soil and groundwater remediation programmes as a chelating agent that keeps contaminants mobile long enough to be extracted.
Feed additive
In animal nutrition, sodium humate is used as a gut-health additive in poultry, swine and aquaculture, typically at 1–3 kg per tonne of feed. It supports intestinal integrity and reduces ammonia in the litter without antibiotic growth promoters.
When to choose sodium rather than potassium
For soil application on sodium-sensitive crops, or in glasshouse production where salinity is already a concern, potassium humate is the correct choice. Sodium humate is appropriate for industrial use, for feed, for non-saline soils where cost per hectare dominates, and for blending where the sodium load can be balanced by calcium.
We supply sodium humate in flake, crystal and powder form from leonardite, with COA including humic acid, moisture, pH and heavy metals. Custom mesh and 25 kg / 1000 kg packing available. Send your specification.
Amino Acid 80%: A Foliar Feeding Guide for High-Value Crops
When a crop stalls — after cold, after transplanting, after a herbicide setback — nitrogen from the soil takes days to show up in the leaf. Free amino acids take hours, because they do not need to be reduced before the plant can use them. That is the whole commercial case for an 80% amino acid powder.
What 80% actually means
The figure refers to the total free amino acid content of the powder, usually produced by enzymatic hydrolysis of soy or feather protein. Enzymatic hydrolysis preserves the L-form of the amino acids, which is the form plants and animals can assimilate. Acid hydrolysis is cheaper but converts part of the content to the D-form and destroys tryptophan.
Ask for the amino acid profile, not only the headline percentage. A product rich in glycine and proline behaves differently from one rich in glutamic acid, and a genuine enzymatic product will state L-form content.
Dilution and timing
| Crop situation |
Dilution |
Rate per hectare |
Timing |
| Vegetables, general |
1:800–1:1000 |
0.75–1.5 kg |
Every 10–14 days |
| Fruit trees |
1:1000–1:1200 |
1.5–2.5 kg |
Bud break, fruit set, sizing |
| Stress recovery |
1:600–1:800 |
1.5–2 kg |
Within 48 hours of the event |
| Greenhouse / fertigation |
1:1000 |
2–3 kg |
Weekly during active growth |
Spray early morning or late afternoon. The leaf surface stays wet longer, and amino acids are taken up through the stomata and the cuticle while the solution is liquid.
Compatibility
- Compatible with most foliar fertilisers, including calcium and micronutrient chelates.
- Do not mix with strongly alkaline products (pH above 9) or with copper-based fungicides in the same tank.
- In hard water, add the amino acid last and keep the final pH between 5.5 and 7.
Four mistakes that waste the product
- Spraying at midday. The droplet dries before absorption and the UV load degrades part of the free amino acid fraction.
- Over-diluting. Below about 1:1500 the uptake is too small to change anything measurable.
- Using it as a nitrogen replacement. At 1 kg/ha the nitrogen delivered is around 160 g — this is a signal product, not a fertiliser.
- Ignoring the profile. Buying on percentage alone gets you a powder that may be mostly glycine with little of the amino acids that drive stress recovery.
Our 80% amino acid powder is enzymatically hydrolysed, fully water soluble, and available in 20 kg bags; the amino humic granule combines the same amino fraction with humate for soil application. Ask for the technical data sheet.